[Cisco] Cisco Router878 G.SHDSL Back-to-Back Configuration

Cisco Router878 G.SHDSL Back-to-Back Configuration
IOS: c870-advipservicesk9-mz.124-4.T8.bin

[R1]G.SHDSL <-----------> G.SHDSL [R2]

test on wire: RJ11 ,4-wire

R1 as CO
R2 as CPE

[R1]

controller DSL 0
mode atm
line-term co
line-mode 4-wire enhanced
dsl-mode shdsl symmetric annex B
line-rate 2048
!
interface ATM0
ip address 192.168.2.1 255.255.255.0
no atm ilmi-keepalive
pvc 0/100
broadcast
encapsulation aal5snap
!
!


[R2]

controller DSL 0
mode atm
line-term cpe
line-mode 4-wire enhanced
dsl-mode shdsl symmetric annex B
line-rate 2048
!
interface ATM0
ip address 192.168.2.2 255.255.255.0
no atm ilmi-keepalive
pvc 0/100
broadcast
encapsulation aal5snap
!      
!

[Verify]

R1#sh controllers dsL 0

DSL 0 controller UP
SLOT 0: Globespan xDSL controller chipset
Frame mode: Utopia
Configured Line rate: 2048Kbps
Line Mode: Four Wire Enhanced Mode
DSL mode: SHDSL Annex B
Line Re-activated 0 times after system bootup
LOSW Defect alarm: ACTIVE
CRC per second alarm: ACTIVE
Line termination: CO

Line 0 statistics

      Current 15 min CRC: 0
      Current 15 min LOSW Defect: 0
      Current 15 min ES: 0
      Current 15 min SES: 0
      Current 15 min UAS: 19

      Previous 15 min CRC: 0
      Previous 15 min LOSW Defect: 0
      Previous 15 min ES: 0
      Previous 15 min SES: 0
      Previous 15 min UAS: 0


Line 1 statistics

      Current 15 min CRC: 0
      Current 15 min LOSW Defect: 0
      Current 15 min ES: 0
      Current 15 min SES: 0
      Current 15 min UAS: 19

      Previous 15 min CRC: 0
      Previous 15 min LOSW Defect: 0
      Previous 15 min ES: 0
      Previous 15 min SES: 0
      Previous 15 min UAS: 0

Line-0 status
Chipset Version:  0
Firmware Version:  R3.0.1
Modem Status:  Data, Status 1
Last Fail Mode:  No Failure status:0x0
Line rate:  1032 Kbps
Framer Sync Status: In Sync
Rcv Clock Status: In the Range
Loop Attenuation:  0.9 dB
Transmit Power:  7.5 dB
Receiver Gain:  9.7000 dB
SNR Sampling:  38.9000 dB
Line-1 status
Chipset Version:  0
Firmware Version:  R3.0.1
Modem Status:  Data, Status 1
Last Fail Mode:  No Failure status:0x0
Line rate:  1032 Kbps
Framer Sync Status: In Sync
Rcv Clock Status: In the Range
Loop Attenuation:  1.0 dB
Transmit Power:  7.5 dB
Receiver Gain:  9.7000 dB
SNR Sampling:  38.4860 dB
Dying Gasp: Present

R1#sh atm interface aTM 0
Interface ATM0:
AAL enabled:  AAL5  , Maximum VCs: 10, Current VCCs: 1

VCIs per VPI: 1024,
Max. Datagram Size: 4528
PLIM Type: GSHDSL - 2048Kbps, Framing is Unknown,, TX clocking: LINE
3057 input, 3072 output, 0 IN fast, 0 OUT fast
Avail bw = 2048
Config. is ACTIVE

R1#sh atm map
Map list ATM0_ATM_INARP : DYNAMIC
ip 192.168.2.2 maps to VC 1, VPI 0, VCI 100, ATM0
      , broadcast

R1#ping 192.168.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms